The summer season is finally here. Everybody is outside with their family members and friends. Summer blossoms are blooming and the tree branches are full of leaves. Although the weather may be pleasant outside, you may notice high moisture levels in your home that your blower cannot remove. It’s time to switch on your air conditioning unit.
However, your air conditioning system eventually stops working. Talk about perfect timing. Maybe because you have not cleaned it for a while in the past few seasons. That is precisely the point. Until now, your air conditioner has been resting idle, gathering dust, grime, and debris that can harm your system over time. In reality, even when not being used, your air conditioner requires regular checks to make sure it is fully prepared for the hot summer months.
To avoid having to sit around on a sweltering summer day praying for a certified specialist to conduct an air conditioning service you can find from Luce, you should clean your machine. To give you a head start for summer, and if you don’t like hiring professionals, though that would be better, follow this cleaning guide for a better performance of your ac system.
1. Turn Off the Power Source
The first step is to always keep in mind to turn off the power to your device whenever you proceed with cleaning your air conditioner. Cleaning your AC system while it is running is risky and must be prevented. Find the service panel on the external condenser to switch the power off. This is usually a shut-off packet close to the device. If you can’t find the service box, it is suggested that you turn off the system at the main switchboard.
2. Replace or Just Clean the Aircon Filters
Disinfecting or fixing your air filters is the simplest and most essential step in cleaning your AC unit. Reusable filters are situated in the central heating system or air-handler cabinets located inside or close to the end of a side of your system. To ensure appropriate air flow, clean or consider replacing your filters two times a year or once they become blocked up with dirt, hair, or grime.
3. Clean the Condenser Coils
Start by removing the side and top frames from the condenser unit to sanitize the air conditioner condenser coils. This can be accomplished with a wrench or a nut driver, depending on the type of bolts required. Easily unscrew and draw the side frames from the device. Remove the lid that may be heavy, and prevent yanking on any wires connected to the blower.
Next, start to clean the coils on the outside of your air conditioner with a soft brush. Please exercise extreme caution when trying to clean the coils. Twisting the sensitive fins or coils is not preferred. After cleaning the outside, vacuum the AC condenser coils on the inside.
Then, use an air conditioner coil cleaner to remove tough dirt and dust from the coils. Please avoid spraying the fan or other electrical parts. Instead of bending the fins, flooding the unit, or spraying water on electronic parts, use a garbage bag to protect them.
4. Clear Out Dust Matters from the Condenser
To effectively clean your air conditioner, consider removing leaves and dust from the bottom of the condenser. If your air conditioner condenser has a drain, make sure to clean it out as well.
Vacuum the blower’s fan thoroughly. Then, tighten any loose bolts and nuts. If the fan motor has oil docks, apply a small amount of lightweight oil to them. Remove the excess water from the device. Reassemble the condenser after you’ve finished the task. Remove any grass, twigs, or shrubs that may be interfering with airflow through the condenser.
5. Don’t Forget to Check also the Refrigerant Lines
To avoid energy loss, coolant lines are typically insulated with foam insulation. Such refrigerant tubes connect the evaporator coil to the condenser.
If the sheeting on the refrigerant lines is destroyed, replace it when cleaning your air conditioner to improve system performance. The first step in resolving this problem is to install new foam insulation for the refrigerant lines. You can also use insulating material tape to wrap the refrigerant lines.
6. Test the AC Unit
Once you’ve finished cleaning the core parts of your AC unit, turn on the condenser. You can begin by turning off the thermostat in your home. Next, for both the shutoff box and the main board, turn on the power. Finally, set the thermostat to cool to power up your AC system.